Bedford. Mid-Cities Homes, Forty Years In.
Bedford sits on the Airport Freeway (SH-183/121) between Euless and Hurst, a straight run north from our Arlington shop by SH-360. Phanton Mechanical takes HVAC and electrical calls here for homes and businesses under two Texas licenses: mechanical TACLA124868E and electrical TECL39666.
What We Do in Bedford.
Every trade we run — mechanical, electrical, and solar — is available to Bedford homes and businesses from one licensed, insured team.
Census figures explain most of the work a Bedford house needs. The median home here was built in 1983. About 37% of the city’s housing units went up in the 1980s and another 20% in the 1970s, while only about 13% have been built since 2000. A house from that era is well past the age of its original air conditioner and furnace, and whatever is still original — the duct runs, the return air path, the electrical panel — was sized for the equipment and the household loads of forty years ago. That is why a replacement quote from us looks at the ducts and the panel along with the equipment: a new unit on forty-year-old ductwork is still a forty-year-old system.
Heating in Bedford is mostly electric. The Census Bureau estimates that about 72% of occupied homes heat with electricity and about 26% with utility gas. Electric heat comes in two forms, a heat pump or resistance heat strips in the air handler, and they do not cost the same to run: the U.S. Department of Energy says today’s heat pump can reduce electricity use for heating by approximately 65% compared with electric resistance heating. When an electric furnace or an aging heat pump comes due, that comparison is the first thing we go through with you. For the homes on gas, we repair and replace furnaces as well.
The City of Bedford spells out when a permit is needed. Its Building Inspections pages say that installing heating and air conditioning units, relocating or installing ductwork, and installing exhaust fans require a permit, and so do electric panel upgrades, new outlets or fixtures, and generators. For each of those the city requires a contractor who is licensed through the State of Texas and registered with the City of Bedford, and inspection requests go through the city’s online portal. On a Bedford job that needs one, the permit is pulled under our state licenses and the city’s inspector checks the work.
On the electrical side, our electricians take service calls and troubleshooting, panel and service upgrades, EV charger circuits, ceiling fans and new wiring. In a 1980s house the usual question is capacity: whether the panel has room for a charger, an electric range or a heat pump before anything is added to it. Because the mechanical and electrical licenses belong to the same company, a system replacement that also needs a new circuit or a larger panel is one job with one contractor.
For Bedford businesses we take commercial HVAC service calls and repairs, rooftop unit replacement, ductwork and tenant finish-outs, with the electrical scope behind them. The closest work of ours you can go and look at is a short drive from Bedford: the TruGrocer Federal Credit Union branch on Davis Blvd in North Richland Hills, where the exposed spiral ductwork is part of the ceiling, and the L’Occitane store at Southlake Town Square, where we carried both the HVAC and the electrical trades.
Source: City of Bedford — When Is a Residential Building Permit Required? · City of Bedford — Building Inspections · U.S. DOE — Home Upgrades: Heat Pumps
Residential HVAC & Electrical
Repair, installation, panels, EV chargers, emergency service.
Commercial HVAC Contractor
Repair, rooftop units, ductwork, tenant finish-outs, maintenance contracts.
Solar & Battery Storage
Enphase-certified design, install, and battery integration.
Central Bedford · North Bedford · Harwood Road corridor · Bedford Road corridor · Airport Freeway (SH-183) corridor
The Homes We Work On in Bedford.
U.S. Census Bureau, American Community Survey 2020–2024 five-year estimates for the City of Bedford. These are survey estimates, not exact counts.
Sources: U.S. Census Bureau, ACS 2020–2024 — B25035, median year built · U.S. Census Bureau, ACS 2020–2024 — B25034, year built · U.S. Census Bureau, ACS 2020–2024 — B25040, heating fuel
Our Work Near Bedford.
Completed work you can go and see — the published projects closest to Bedford.
Asked in Bedford.
Do I need a permit to replace my air conditioner or furnace in Bedford?
Yes. The City of Bedford says mechanical work such as installing heating and air conditioning units, relocating or installing ductwork, or installing exhaust fans requires a permit, and that the contractor must be licensed through the State of Texas and registered with the City of Bedford. Electrical work such as panel upgrades, new outlets or fixtures, and generators is on the same list. Inspection requests go through the city’s online portal.
My Bedford house was built in the 1980s. Should I expect more than an equipment swap?
Often, yes. The median Bedford home dates from 1983, so the ductwork, the return air path and the electrical panel can be older than any equipment that has been replaced since. We check those three things before quoting a system, so that a duct repair or a panel upgrade shows up in the quote and not as a surprise halfway through the job.
Do you come to Bedford from Arlington?
Yes. Our shop is at 615 Stadium Dr E in Arlington, and Bedford is north of us by SH-360 and the Airport Freeway. We take residential and commercial calls Monday through Saturday, 8AM to 9PM, and Sunday by appointment; after-hours emergency calls go to the on-call technician.
Need a contractor in Bedford?
Hours: Mon–Sat 8AM–9PM · Sunday by appointment. Emergency calls route to on-call technicians.
Also serving: Arlington, TX · Fort Worth, TX · Grand Prairie, TX · Frisco, TX · North Richland Hills, TX · Mansfield, TX · Irving, TX · Dallas, TX · Euless, TX · White Settlement, TX · Burleson, TX · Weatherford, TX

